アプリケーション
電流検出と電流源
機能
すべて
検索基準に一致する回路
下の回路が、選択された検索基準に一致します
–48V Low Side Precision Current Sense “Classic” High-Precision Low Side Current Sense ±5A、2.5V (2象限) μModule 電圧レギュレータ 0A to 2A Current Source 1-Cell Monitor with Bottom-Side Sense 12.5W PWM Heat Source 120W Supply Monitor Includes ICC of LT2940 16-Bit Resolution Unidirectional Output into LTC2433 ADC 2-Terminal Temperature-to-Current Thermometer Suitable for Use at the End of Long Wire Runs 2.7V to 5.5V Precision High Side Current Sense 2.7V to 5.5V Ultra High Precision Current Sense 28V Power to Frequency Converter 4mA~20mAのループからの3.3V/10mAレギュレータ Micropower Integrating Current Sense 4mA~20mAループ・トランスミッタ 48V Power Monitor With Opto-Isolated Serial Interface 48V Supply Current Monitor with Isolated Output and 105V Survivability AC Current Measurement AC Power and Current Monitor Adjustable 0W to 10W Load Box with UVLO and Thermal Shutdown Adjustable Two Terminal 200mA Current Source Armature Current Monitor for DC Motor Applications Bidirectional Battery-Current Monitor Bidirectional Current Sense Circuit with Separate Charge/Discharge Output Bidirectional Current Source Bidirectional H-Bridge Monitoring with ADC-Friendly Differential Output Bidirectional H-Bridge Monitoring with Single-Ended Output ラッチによる負荷切断と早期警報表示による回路フォールトに対する保護 高速ラッチによる負荷切断を使った回路フォールトに対する保護 DAC Controlled 100mA Current Source Eight Decade Current Sensing Log Amplifier Full-Bridge Load Current Monitor Fully Isolated AC Power and Current Monitor Ground Referred Precision Current Sources High Accuracy 10mA Current Source High Side Current Sense and Fuse Monitor High Side Current, Input Voltage and Open Fuse Monitoring with a Single LTC4151 High Side Power Sensing with Onboard ADC and I2C High Side Power Sensing with Onboard ADC and I2C High Voltage 100mA Current Source High Voltage/Current and Temperature Monitoring 産業用センサの4mA~20mA電流ループ・パワー・タップ Integrating Watt-Hour Meter 4mA~20mA電流ループの絶縁 Isolated Current and Voltage Monitor Isolated Power Line Monitor Load Monitor Alarms Above 60W Low Power, Bidirectional 60V Precision Hi Side Current Sense Low Side Current Sense Motor Monitor with Circuit Breaker Motor Protection/Regulation モータの保護/安定化 過電流および低電圧バッテリ・フォールトに対する保護 過電流バッテリ・フォールトに対する保護 Parallel Current Sources For Higher Current 300mA Output Positive Supply Rail Current Sense With Over-the-Top Op Amp Practical H-Bridge Current Monitor Offers Fault Detection and Bidirectional Load Information Precision Current Sink Precision Current Source Precision Ground Referenced Voltage Controlled Current Source Precision Nanoamp Bidirectional Current Source Precision Voltage Controlled Current Source プログラム可能な1.5A スイッチング電流源 Reduced Power Infra-Red Diode Driver Secondary-Side AC Circuit Breaker Self-Powered High Side Current Sense Simple 500V High Side Current Monitor Simple Bidirectional DC Motor Speed Controller DCモータの簡略化トルク制御 DCモータの簡略化トルク制御 Solenoid Current Monitor for Ground Tied Solenoid Solenoid Current Monitoring Split or Single Supply Operation, Bidirectional Output into A/D Temperature Monitoring with an NTC Thermistor While Measuring Load Current and LTC4151 Supply Current Thermally Controlled NiCad Charger Two Terminal 1A Current Source 2端子3A電流源 Two Terminal 500mA Current Source Two Terminal Current Regulator Two Terminal Current Source Voltage Controlled Current Source Voltage Controlled Current Source with Ground Referred Input and Output Wide Input Range 10W PWM Heat Source
–48V Low Side Precision Current Sense
This amplifier configuration is essentially the complementary implementation to the classic high-side configuration. The op amp used must support common-mode operation at its lower rail. A “floating” shunt-regulated local supply is provided by the Zener diode, and the transistor provides metered current to an output load resistance (1kΩ in this circuit). In this circuit, the output volt-age is referenced to a positive potential and moves downward when representing increasing –48V loading. Scaling accuracy is set by the quality of resistors used and the performance of the NPN transistor.
Loading